Taylor TX Polished Concrete Floor Specialists
We do polished concrete in Taylor and across eastern Williamson County. That covers older downtown commercial slabs along Main Street, newer homes, and industrial warehouse floors near US-79 and SH-95. Whatever the floor, we start by looking at the slab in person. When the job calls for it, we grind a test area to show how the concrete polishes. We put the scope in writing before the main job starts.
- We cover Taylor
- An estimator reviews your project
- Based in Austin, 20+ years in the trade
- More than 20 years in the concrete trade
- An estimator reviews your project
- A written scope for your project
- Austin and the Central Texas towns we cover
Sound Familiar?
Homeowners, remodelers, builders, and facility managers around Central Texas often bring us these four problems.
You don't know what's under the floor
Tile or carpet comes up and nobody can say whether that slab will polish well. We check it first, and when the job calls for it we grind a test area, so there's less guessing about the finish.
Polishing, grind and seal, epoxy, and staining all get sold as "shiny concrete"
They're different systems with different upkeep, and we'll tell you which one fits the space instead of selling whatever we installed last week.
Cracks over Central Texas clay
Clay soil that swells and shrinks moves slabs. We can repair and manage cracks before polishing, but polishing won't erase them, and an overlay won't cure the movement. Most of Taylor sits east of Interstate 35 on Blackland Prairie clay, which is deep and dense, so we look closely at crack history here. See how Central Texas clay affects polished floors.
Commercial downtime is a real cost
In retail, office, and warehouse spaces, we can work in zones and stages and give you our honest estimate of when you'll get each area back. We won't just promise to "work around you."
Whatever the worry, we start the same way: we check the slab first, then recommend the system we think fits it best.
Send us photos of your slabConcrete Flooring Services in Taylor
We do polished concrete in Taylor and across eastern Williamson County. That covers older downtown commercial slabs along Main Street, newer homes, and industrial warehouse floors near US-79 and SH-95. Whatever the floor, we start by looking at the slab in person. When the job calls for it, we grind a test area to show how the concrete polishes. We put the scope in writing before the main job starts.
The crews and written scopes behind our polished concrete floors in Austin make the drive out US-79 to Taylor too.
Floors We Put Down in Taylor
Core specialty Polished Concrete
We do concrete polishing in Austin on slabs that can take it, grinding and polishing toward the finish we agree on with you.
Read the details
Residential Polished Concrete
We install residential polished concrete in Austin, from remodels to custom builds. When the job calls for it, we grind a sample on your slab before we agree on the finish.
Read the details
Commercial Polished Concrete
We install commercial polished concrete in Austin for retail, office, and warehouse spaces, and we plan the work in stages around how your business runs.
Read the detailsEvery project starts with an on-site evaluation. Actual scope, pricing, and expected results depend on your specific substrate condition, environment, and project requirements. The website describes our services in general terms. Your signed proposal governs the actual work.
How We Work in Taylor
- More than 20 years in the concrete trade
- We check the slab in person, with a test area when it helps, before we agree on a finish
- Years of work on historic downtown commercial floors and modern industrial slabs
- A written scope that lists prep, repairs, how much stone shows, shine level, and treatments
- We walk you through care and upkeep in person when we finish
Planning Taylor Jobs Around Travel and Access
Taylor sits about 30 miles northeast of Austin along US-79. We book it alongside Hutto and Georgetown jobs so our crews travel once and work a full day on site. Downtown buildings on Main Street and Second Street can have narrow doors and little room to unload, so we check parking, door width, and power ahead of time.
Homes across Taylor are easy to get our floor grinders and dust extraction units into. Industrial and warehouse spaces near the US-79 and SH-95 junction usually have open room to set up for bigger grinding jobs. If a retail or commercial space stays open, we can do the floor one zone at a time outside business hours, with HEPA dust extraction on the grinders.
What We Find in Taylor Slabs
In Taylor we see everything from downtown commercial buildings more than a century old to modern industrial sites and newer subdivisions. Older downtown commercial slabs often carry decades of coatings, glue, and patches, so they need repair, grinding, and a close look before we agree on a decorative finish.
Newer home slabs in Taylor's growing neighborhoods are usually flat and properly cured. A cream finish with almost no stone showing works on them, and so does salt and pepper, where fine flecks of stone show through. Depending on the slab, we often finish with a lithium silicate hardener. Garage floors in Taylor homes can get either a polished finish or an epoxy coating, based on how you'll use the space and what chemicals hit the floor. Floors in Taylor's industrial area near US-79 usually need a semirigid joint filler, which is firm but gives a little, and a hardener picked for forklifts and heavy foot traffic.
Areas we cover here
Our Taylor work all happens on site. We don't have a showroom or an office in town, so when your job calls for samples or mockups, we bring them to you.
How a Polished Concrete Project Runs
Most jobs go through four steps between your first photos and the first day of grinding, and we don't like to rush them.
-
Send details and photos
Your floor area, how you use the space, what's on the floor now, and a few photos of the slab. That's usually enough for a first read on whether polishing is realistic.
-
We check the slab
On site we look at things like hardness, how deep the stone sits, flatness, anything soaked into the concrete, cracks, and old repairs. When the job calls for it, we grind a small test area so you can see your own concrete polished before you choose.
-
We talk through which systems fit
Mechanical polishing, grind and seal, an epoxy coating, or a polishable overlay. We'll make a clear recommendation, even when it's a different system from the one you asked about.
-
Written scope, then the work
Prep, repairs, the finish, treatments, phasing, and anything left out of the job all go on paper first. Then our crew does the work as written. We'll go over dust control for your space during the consultation.
Not sure whether your slab should be polished, overlaid, or coated?
Send us photos and a rough floor area. One of our estimators usually looks them over within 24 business hours and gives you a straight answer.
What Customers Tell Us
Here's what some of our customers have said.
“We removed dated tile in our Barton Creek remodel. The team prepped the uneven slab, walked us through our options, and we ended up with a satin cream finish we really like.”
“As a commercial GC, it's rare to find a flooring trade in Austin that explains the prep and testing this well. They kept us updated on the schedule the whole way through.”
Individual results vary based on use, maintenance, and environmental conditions.
Taylor Questions
Is Taylor within your concrete polishing service area?
Can an old downtown Taylor commercial slab be polished?
Do you polish industrial and warehouse floors in Taylor?
How much does concrete floor polishing cost in Taylor?
How long does a polishing project take in Taylor?
Where can I find a concrete floor specialist near Taylor?
What are the downsides of polished concrete floors?
Is polished concrete cheaper than tile for a Taylor home?
Does a Taylor slab need repair before polishing?
Still have a question about your floor?
Send it our way, with photos if you have them. We'll get back to you as soon as we can with a straight answer, whether or not you hire us.
Get My Polished Concrete QuoteNear Taylor
We schedule nearby communities together, which keeps travel down and makes site visits easy to set up.
Polished concrete in Taylor?
Tell us roughly how big the floor is and how you use it, and add a few photos of the slab. We'll look it over and get back to you with a next step.
- We check your slab before we quote
- Your signed proposal spells out what's not included
- We walk you through care in person when the job is done